Patio
shops, refinishers and OEMs have used Patio Products'
wide selection of furniture components to help them in
the procurement of hard to find outdoor patio furniture
replacement parts. We stock nylon inserts, snap rivets,
caps, glides, stem bumpers, metal clips, umbrella parts,
sled runners, tire extrusions, wheels, aluminum wheel
hubs, adjustment brackets, sling inserts, seat post
bushings, fiberglass chair springs and other
miscellaneous parts.
Please make sure that the thread size of your part is 1/4-20 (not metric). (30-410 & 30-411B are sold separately)
Please make sure that the thread size of your part is 1/4-20 (not metric). (30-400 & 30-411W are sold separately)
30-400 - Nylon 1/4-20 Thread Insert fits 7/16" hole (Part #30-411 fits into this thread insert.) Clear Polycarbonate
ea.
30-410 - Nylon 1/4-20 Thread Insert fits 3/8" hole (Part #30-411 fits into this thread insert.)
ea.
30-411W - 1/4-20 Thread with approximately 5/8" Stainless Steel Threaded Stud Adjustable Glide 1.05" Diameter Nylon Non-Skid Base (This adjustable glide fits into Part #30-410.) White
ea.
30-411B - 1/4-20 Thread with approximately 5/8" Stainless Steel Threaded Stud Adjustable Glide 1.05" Diameter Nylon Non-Skid Base (This adjustable glide fits into Part #30-410.) Black
ea.
30-412W - 5/16-18 Thread with approximately 5/8" Stainless Steel Threaded Stud Adjustable Glide 1.05" Diameter Nylon Non-Skid Base White
ea.
30-412B - 5/16-18 Thread with approximately 5/8" Stainless Steel Threaded Stud Adjustable Glide 1.05" Diameter Nylon Non-Skid Base Black
ea.
30-413W - 8 mm (millimeter) x standard 1.25 thread with approximately 5/8" Long Stainless Steel Threaded Stud Adjustable Glide .911" Diameter Nylon Non-Skid Base White
ea.
30-413B - 8 mm (millimeter) x standard 1.25 thread with 1/2" Long Stainless Steel Threaded Stud Adjustable Glide .911" Diameter Nylon Non-Skid Base Black
ea.
30-414W - 6 mm (millimeter) x standard thread with 1/2" Long Stainless Steel Threaded Stud Adjustable Glide .911" Diameter Nylon Non-Skid Base White
ea.
30-414B - 6 mm (millimeter) x standard thread with 1/2" Long Stainless Steel Threaded Stud Adjustable Glide .911" Diameter Nylon Non-Skid Base Black
30-902 - Round Hinge Fits 1" Outside Diameter Round Tube
ea.
30-905 - 9" Glider bearing Arm 7 1/2" Hole To Hole
9" is the measurement from end to end. It is made of steel and is zinc coated with silver chromate. You can spray paint over the chromate. Hangers are bolted to the frame (bolts not included). Bolt lengths and diameters would depend on original part sizes. Re-use or try to match the original bolts. We suggest stainless steel with locknuts.
ea.
30-906 - 10" Glider bearing Arm 8 5/8" Hole To Hole
10" is the measurement from end to end. It is made of steel and is zinc coated with silver chromate. You can spray paint over the chromate. Hangers are bolted to the frame (bolts not included). Bolt lengths and diameters would depend on original part sizes. Re-use or try to match the original bolts. We suggest stainless steel with locknuts.
ea.
30-912 - 1/2" Axle Cap
ea.
30-938 - Wheel Bushing for 1/2" Axle
ea.
30-936 - Metal Pop Rivet Glide 15/16" OD - Fits 3/16" - 1/4" hole Set includes glide and pop rivet
30-934 - Heavy Duty Aluminum Rocker Plate Swivel Seat Post 1 1/2" center hole to center hole. Our new part is aluminum and does not rust. You can paint or powder coat them to match frame of furniture. Does not include rocker spring plates, rectangular washers, bolts, nuts and plastic seat post bushings. Recommend 1/4" Stainless Steel hex head bolts and lock nuts
ea.
30-935 - Keeper Plate 1 1/2" center hole to center hole
ea.
30-933 - Straight Heavy Duty Aluminum Swivel Seat Post 5 1/4" hole to hole. Our new and improved seat post replaces the old rusted seat post. The old part would collect water and cause it to rust out. Our new part is aluminum and does not collect water. You can paint or powder coat them to match frame of furniture. Does not include bolts, nuts and plastic seat post bushings. Recommend 1/4" Stainless Steel hex head bolts and lock nuts
ea.
30-931 - Angled (7.5°) Heavy Duty Aluminum Swivel Seat Post 5 1/4" hole to hole. Our new and improved seat post replaces the old rusted seat post. The old part would collect water and cause it to rust out. Our new part is aluminum and does not collect water. You can paint or powder coat them to match frame of furniture. Does not include bolts, nuts and plastic seat post bushings. Recommend 1/4" Stainless Steel hex head bolts and lock nuts
30-918 - Rocker Spring Plate 1/4" x 2 1/2" x 5" Fiberglass Rocker Spring Plate
The 30-918 is only available in black. The black finish was added to the spring plate by the manufacturer because it has an ingredient that makes it possible for the furniture manufacturers to powder coat the chair frames after they are assembled. The black finish will hold an electrostatic charge that attracts the powder. You can spray paint the plates with aerosol paint from a local paint or hardware store. You should be able to find an aerosol paint that will come close to matching the original considering most of the spring plate is not exposed.
Fiberglass Rocker Spring Plates do not have holes drilled. You will need to use the old spring plate as a template to measure and drill hole to fit your furniture. It is suggested that you use a drill press to make sure the holes are straight. Re-assemble the parts the same way that you took them apart. There should be a metal plate or washer between the bolt head and the spring plate.
ea.
30-919 - Rocker Spring Plate 1/4" x 3" x 5" Fiberglass Rocker Spring Plate
The 30-919 is only available in black. The black finish was added to the spring plate by the manufacturer because it has an ingredient that makes it possible for the furniture manufacturers to powder coat the chair frames after they are assembled. The black finish will hold an electrostatic charge that attracts the powder. You can spray paint the plates with aerosol paint from a local paint or hardware store. You should be able to find an aerosol paint that will come close to matching the original considering most of the spring plate is not exposed.
Fiberglass Rocker Spring Plates do not have holes drilled. You will need to use the old spring plate as a template to measure and drill hole to fit your furniture. It is suggested that you use a drill press to make sure the holes are straight. Re-assemble the parts the same way that you took them apart. There should be a metal plate or washer between the bolt head and the spring plate.
ea.
30-920 - Rocker Spring Plate 5/16" x 2" x 7.026" Fiberglass Spring Plate
30-408 - Steel Weld Cup 1 1/2" Inside Diameter Steel Cup for Replacing Wrought Iron Welded Foot Center hole is 3/8" diameter (Parts #30-612, #30-612b and #30-614 fit into this metal weld cup.)
ea.
The 30-408 - 1 1/2" I.D. Steel Weld Cups are unfinished and may have surface rust when you receive them. These parts are made to be welded to the legs of wrought iron furniture. They cannot be zinc plated, anodized, galvanized or metalized because those finishes will cause harmful fumes for the welder. It is impossible to completely stop unfinished steel parts from rusting on the surface. The 30-408 parts are coated with oil to help reduce the amount of oxidation that causes rust. They should be degreased by cleaning with soap and hot water before they are welded or painted. The welding will cause the part to burn so you will need to clean the welded foot after the welding by sanding, wire wheel polishing or sand blasting before they are prepared for paint.
30-612 - 1 1/2" Deluxe Insert Glide Fits an 1 1/2" Inside Diameter Metal Weld Cup (part #30-408) (for Wrought Iron) White
ea.
30-612B - 1 1/2" Deluxe Insert Glide Fits an 1 1/2" Inside Diameter Metal Weld Cup (part #30-408) (for Wrought Iron) Black
ea.
30-614 - 1 1/2" Round Plastic Insert Glide Fits an 1 1/2" Inside Diameter Metal Weld Cup (part #30-408) (for Wrought Iron)
30-409 - Steel Weld Cup 1 1/4" Inside Diameter Steel Cup for Replacing Wrought Iron Welded Foot Center hole is 3/8" diameter (Parts #30-611 and #30-613 fits into this metal weld cup.)
ea.
The 30-409 - 1 1/4" I.D. Steel Weld Cups are unfinished and may have surface rust when you receive them. These metal parts are made to be welded to the legs of wrought iron furniture. They cannot be zinc plated, anodized, galvanized or metalized because when they are welded to the frame, those finishes will cause harmful fumes for the welder. It is impossible to stop unfinished steel parts from rusting on the surface. The 30-409 Weld Cups are coated with a phosphate coating to help reduce the oxidation that causes surface rust. The welding will cause the part to burn so you will need to clean the welded foot after the welding by sanding, wire wheel polishing or sand blasting before they are prepared for paint.
30-611 - 1 1/4" Deluxe Insert Glide Fits an 1 1/4" Inside Diameter Metal Weld Cup (part #30-409) (for Wrought Iron) Natural
ea.
30-611B - 1 1/4" Deluxe Insert Glide Fits an 1 1/4" Inside Diameter Metal Weld Cup (part #30-409) (for Wrought Iron) Black
ea.
30-613 - 1 1/4" Round Plastic Insert Glide Fits an 1 1/4" Inside Diameter Metal Weld Cup (part #30-409) (for Wrought Iron)
30-639B - 1/2" Round Tapered Cap Fits over 1/2" Outside Diameter Hollow or Solid Tube 1/2" Inside Diameter Black Nylon
Black
ea.
30-733 - 15/16" Disk Cap Fits over 15/16" Diameter Flat Metal Flange Cap Outside Diameter 1 1/8" White Nylon
White
ea.
30-733B - 15/16" Disk Cap Fits over 15/16" Diameter Flat Metal Flange Cap Outside Diameter 1 1/8" Black Nylon
Black
ea.
30-733 - P1128 - 15/16" Disk Cap Fits over 15/16" Diameter Flat Metal Flange Cap Outside Diameter 1" Fits Carter Grandle - Park Lane Montaigne, Savoy, Bridgeport, Carlyle
ea.
30-724 - 1 1/4" Disk Cap Fits over 1 1/4" Diameter Flat Metal Flange Cap Outside Diameter 1 7/16"
Natural
ea.
30-725 - 1 7/16" Disk Cap Fits over 1 7/16" Diameter Flat Metal Flange Cap Outside Diameter 1 5/8" Clear Vinyl
Vinyl
ea.
P1125 - 1 1/2" Disk Cap Fits 1 1/2" Diameter Metal Flange Cap Outside Diameter 1 11/16"
ea.
30-726 - 1 3/4" Disk Cap Fits over 1 3/4" Diameter Flat Metal Flange Cap Outside Diameter 1 15/16"
Natural
ea.
30-738 - 1 5/8" Disk Cap Fits over 1 5/8" Diameter Flat Metal Flange Cap Outside Diameter 1 7/8"
White
ea.
30-738B - 1 5/8" Disk Cap Fits over 1 5/8" Diameter Flat Metal Flange Cap Outside Diameter 1 7/8"
30-903 - 2" Table Umbrella Hole Ring Set Fits 2" Umbrella Hole in a .22" to .25" thick Glass or Acrylic top includes vinyl grommet and clear plastic cap
ea. set
30-937 - 1 3/4" Table Umbrella Hole Ring Set Fits tightly into a thick 1 3/4" Table Umbrella Hole 1 9/16" Inside Diameter Umbrella Pole Hole Fits 1 1/2" Outside Diameter Umbrella Pole
ea. set
30-914 - Table Rim Clip 1 5/16" X 3/4" Supports Glass and Acrylic Table Tops in Rim Natural Nylon
ea.
30-914B - Table Rim Clip 1 5/16" X 3/4" Supports Glass and Acrylic Table Tops in Rim Black Nylon
ea.
30-915 - Table Rim Attachment Clip 1.42" X .77" Screws into table leg to attach rim to table leg - Natural Nylon Screw not included.
ea.
30-915B - Table Rim Attachment Clip 1.42" X .77" Screws into table leg to attach rim to table leg - Black Nylon Screw not included.
ea.
30-916 - Table Rim Clip 1.575" X .760" Nylon Clip Supports Glass and Acrylic Table Tops in Rim - White Nylon Table Rim Clips are used to secure the glass or acrylic top up into the removable table rim. They do not screw on. They are bent to push the top up into the rim.
ea.
30-916B - Table Rim Clip 1.575" X .760" Nylon Clip Supports Glass and Acrylic Table Tops in Rim - Black Nylon Table Rim Clips are used to secure the glass or acrylic top up into the removable table rim. They do not screw on. They are bent to push the top up into the rim.
ea.
30-917 - Table Rim Clip 1.230" X .765" Nylon Clip Supports Glass and Acrylic Table Tops in Rim - White Nylon
ea.
30-917B - Table Rim Clip 1.230" X .765" Nylon Clip Supports Glass and Acrylic Table Tops in Rim - Black Nylon
30-904 - 4- Position Adjustment Bracket (White Nylon) 9 7/16" L x 1/2" W
This part may be screwed or riveted to the frame. (Attachments not included) Stainless self tapping screws are suggested. The screw holes are recessed. The screw size would depend on the frame hole size. If you are replacing the exact same bracket, the holes should match up. If they do not, you can use the bracket as a template to mark and drill new holes. Make sure that the two brackets are lined up the same on either side of the frame.
White Nylon
ea.
30-904B - 4- Position Adjustment Bracket (Nylon) Black 9 7/16" L x 1/2" W
This part may be screwed or riveted to the frame. (Attachments not included) Stainless self tapping screws are suggested. The screw holes are recessed. The screw size would depend on the frame hole size. If you are replacing the exact same bracket, the holes should match up. If they do not, you can use the bracket as a template to mark and drill new holes. Make sure that the two brackets are lined up the same on either side of the frame.
Black
ea.
30-904 - P1201 - 4- Position Adjustment Bracket (Nylon) 9 7/16" L x 1/2" W
This part may be screwed or riveted to the frame. (Attachments not included) Stainless self tapping screws are suggested. The screw holes are recessed. The screw size would depend on the frame hole size. If you are replacing the exact same bracket, the holes should match up. If they do not, you can use the bracket as a template to mark and drill new holes. Make sure that the two brackets are lined up the same on either side of the frame.
ea.
30-908 - 6- Position Adjustment Bracket (White) 10 5/8" L x 5/8" W
This part may be screwed or riveted to the frame. (Attachments not included) It fits on a round tube. It may not be the same as the ones you want to replace, but you should be able to adapt it to work for you. It is attached with aluminum rivets or stainless self tapping screws.
White Nylon
ea.
30-921 - 20-1/2" Adjustment Bracket Protector (Chair Protector) Fits 1" to 1 1/4" Outside Diameter Tubing Protects the chair frame from being scratched by adjustment bracket
This part may be cut with hacksaw or band saw. It is made of clear rigid P.V.C.